Install the "MALL PGM" fuse back into the fuse panel and test remote(s). Repeat step 7 now for each additional remotes to be programmed including any existingġ0. *** that will confirm successful programming.Ĩ. It is necessary to wait approximately 14 seconds for a second chime ************* IMPORTANT: After 7 seconds, a chime may be heard confirming successful Press and hold the remote LOCK and UNLOCK buttons simultaneously for 14 seconds. A chime will be heard when the system enters intoħ. Turn the key to OFF and then back to ACC within 1 second.Ħ. Insert the key into the ignition, and turn to the ACC position.ĥ. *** owner's manual to properly locate the "MALL PGM" fuse.Ĥ. Remove the "MALL PGM" fuse from the fuse panel. The other remotes will not be functional until youģ. IMPORTANT: Before entering programming mode, have in possession all of the remotes you Remove the ignition key in order to exit the Program Mode. Perform the previous step to program up to four transmitters (including yourġ1. Transmitter has been successfully programmed (this take approximately 15ġ0. Transmitter and hold until the vehicle beeps twice to verify that the Press the LOCK and UNLOCK buttons together on the keyless entry Verify the Program Mode has been activated.ĩ. The vehicle will sound three beeps in order to Ignition key in the lock cylinder.) Leave the ignition key in the ignition lockĨ. Insert the ignition key into the ignition lock cylinder. (Do not turn the ignition key in the lock cylinder.)ħ. Insert the ignition key into the ignition lock cylinder and remove the key. | (Do not turn the ignition key in the lock cylinder.)Ħ. Press and hold the driver side door lock switch in the UNLOCK position.ĥ. Turn ignition OFF and remove the key from the ignition.Ĥ. Insert key in ignition and turn to ON (As far as you can without cranking engine)ģ. The other remotes will not be functional until you program the remotes again.Ģ. Once you program the remotes, all previous codes will be erased from the memory. IMPORTANT: Before entering programming mode, have in possession all of the remotes you will be using on the vehicle. Disconnect programming connector wire from ground to exit programming Repeat step 4 for to program any additonal keyless remotes includingĪnd existing keyless remotes. System will respond by lockingĪnd unlocking doors one time to indicate successful programming.ĥ. System will now lock and unlock doors automatically to indicateĤ. Leave connector wire connected to ground through out procedure.ģ. The programming connector wire should have one termial in the plasticĬonnector on end of black/white wire. You may have to pull back right side trunk trim on trunk wall to locateĢ. Locate the programming connector wire located in the RH trunk area. Replacing your intake system with an aftermarket unit will increase intake noise, performance, and improve your overall driving experience.Note: Existing keyless remotes will be erased with this procedure.Įxisting working remotes will have to reprogrammed also.ġ. Often times, the factory airbox is restricting. We often recommend upgrading your OEM intake to a cold air intake as one of the first modification your should do to your car. They are quick and simple to install while also enhancing the looks of your engine bay, the sounds of your engine, and the performance of your vehicle. Air Intake SystemĪir intake systems are a common first mod to many project cars. Spectre 11-19 Ford Explorer V6-3.5L F/I Air Intake Kit - Polished Aluminum w/Red Filter. Spectre air intake systems are designed to get more horsepower and torque from your vehicle while working to protect your engine from harmful debris. Spectre air intakes come with couplers, stainless steel clamps, bracket, velocity stack, and all necessary hardware for an OE fit and finish. This air intake system comes with a washable, reusable low restriction Spectre air filter, polished aluminum intake tubing and a black powder coated heat shield to help prevent heated engine air from entering the intake inlet. Spectre 11-19 Ford Explorer V6-3.5L F/I Air Intake Kit - Polished Aluminum w/Red Filter
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |